Commercial sink faucets are used each and every day by a lot of people. And when we use it that often, minerals build up and the performance level can drop a lot. That is when you really need to replace the commercial sink faucet. 

Also, to get a taste of the new features and make an upgrade with the technology, many people tend to change it and you can look for the prefessional commercial plumber San Jose.

But, how to replace a commercial sink faucet?

In this article, I’ll discuss the step-by-step process of changing the commercial kitchen faucet. Keep reading to learn how to do it all by yourself in just around one hour. Also, have a look at the top common questions in the last section.

Replacing Commercial Sink Faucet – DIY Guide

It isn’t the easiest thing to do to change your faucet all by yourself. But if you follow these guidelines properly you won’t need a plumber. So, take your time, go through the steps accurately and get ready to get a whole new look on your sink.

Things You’ll Need

  •  A New Faucet
  • Basin Wrench 
  • Sponge 
  •  Towels
  •  Plumber’s Tape
  • Lubricant Spray
  • A Bucket
  • Wire Brush 
  • A helping hand or a Friend

Now, replacing the entire commercial faucet includes two major steps. The first one is to get rid of the old dirty faucet and the second step is installing the new one.

Sounds so easy right? Haha, not that much. But I assure you if you follow these easy beginner friendly steps you’ll be able to pull it off.

Removing the Old Kitchen Faucet

  1. Clearing Out Everything Under the Sink

Do you know what the first thing many plumbers do before starting their main work is? They inspect under the sink. 

It is most likely that you’re going to have to spend a lot of time under your kitchen sink. And to do that, get all the things out of there. You might have items like spray cleaners, brushes, sponges, etc. Remove everything.

Now put a towel underneath so that you don’t get yourself all messed up.

  1. Turning off the water supply

You will find water valves under the sink. They need to be turned off.

You can see two valves, right? Well, the left one is usually for hot water, and the right one is for cold water. Turn the valves clockwise to shut them off. Last time I did it, I found mine stuck, so I used a pair of pliers. You can use it too.

  1. Detaching the Water Supply Lines

It is somewhat similar to step number two. The lines are connected to hot and cold water valves at the bottom of the sinks.

Slowly turn the nuts clockwise to disconnect them. Finding it hard? Use a basin wrench. Trust me, they are a lifesaver.

Always remember to keep a bucket near you. just in case there is any sort of leakage or water breaks out.

  1. Detaching the Faucet

Now you have to detach the faucet. Here is where your friend comes in to help. From above the cabinet, he has to hold the faucet.

While he’s holding the faucet, you have to loosen the nuts, and your friend will lift the old faucet out of the sink.

But hey, remember, the average lifespan of faucets is usually 15 to 20 years. So, if you are changing it after a long time, there is a high chance that you will find the nuts barely stuck. You won’t be able to loosen them that easily.

What to do? Put some lubricant spray on the nuts and take a break for at least half an hour. That should do it. But you can always wait a little longer.The nuts will loosen up.

  1. Cleaning Up

After you and your friend have removed the old faucet, it is time to do some cleaning. There is always some sort of grime around the sink. Sponge it with water to remove any grime that has accumulated. 

Installing the New Faucet

Before installing the new faucet, you have to get yourself a brand new commercial faucet that will include distinctive and strong features to make your kitchen life easier.

I suggest you take a look at the following article for a review of the best commercial kitchen faucets. 

Now, let’s take a look at how to install a new kitchen faucet.

  1. Deck Plate Installation

Faucets are usually used for a three- or one-hole kitchen sink. The deckplate is there for the extra holes.

Now place the plastic gasket and set up the deck plate. It is quite easy, and you can take help from the manufacturer’s instructions.

  1. Putting the Faucet Through the Holes

In the second step, you need to put all the faucet lines through the holes.

So hold the brand new faucet over the counter, and then drop the faucet lines through the holes. This step is easy, but at the same time, it is really important.

So take your time and make sure the faucet is in its perfect place.

  1. Installing Washers and Nuts

Here’s where the main stuff begins. You need to install washers and nuts in order to hold the faucet. So, underneath the sink, install the nuts very carefully, and, oh, one more thing.

Check the faucet again before tightening the nuts.

  1. Connecting the water supply lines

When you buy a new commercial sink faucet, you will get new water lines. So, you do not have to worry about the old dirty ones even if they are completely ruined.

To connect the water lines, my suggestion would be to use a plumber tape. You need to connect these lines accurately. And to do that wrap up the threads using the tape.

And now use the wrench again to  screw them into the water lines.

  1. Searching Leakage Problems

You are almost done, just the testing parts are left.

Having leakage problems anywhere around the sink can be one of the most frustrating things. So, turn on the water and check if you are facing any leakage problems. 

Try to turn it on slowly and test it multiple times. 

That’s it. Enjoy your brand new faucet! 

Frequently Asked Questions

  1. How much does it cost to install a Kitchen faucet?

Answer: On average, installing a kitchen faucet can cost you anywhere between $150 to $400. 

  1. How long should it take a plumber to replace a kitchen faucet?

Answer: Most of the Plumbers would take around 45 minutes to 1 hour to replace your kitchen faucet. However, sometimes plumbers can get the work done even in 30 minutes. 

  1. Is it Possible to change the kitchen faucet without a Plumber? 

Answer: Yes, it certainly is. Replacing the kitchen faucet is one kind of DIY job. 

So, if you have a little bit of knowledge about plumbing and follow the correct process, you can easily pull it off. 

  1. Will replacing a faucet stop it from leaking?

Answer: If you want to change your faucet just to stop it from leaking, then it’s a bad idea. You can always get it repaired.  It will solve the problem and at the same time save you from unnecessary spendings. 

Bottom Line

Replacing the commercial sink faucets is one of the simplest jobs for the plumbers.  

But if you have a good idea and follow the process correctly, you can easily replace it all by yourself. 

Again, if you find it hard or face complications along the way, it is always better to call a good plumber.